Difference between revisions of "Banana Pi BPI-M2+"
(→Hardware interfact) |
(→Hardware spec) |
||
| Line 12: | Line 12: | ||
==Hardware spec== | ==Hardware spec== | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! | ||
| + | ! Banana Pi M2+(Plus) | ||
| + | |- | ||
| + | ! CPU | ||
| + | | H3 Quad-core Cortex-A7 H.265/HEVC 4K | ||
| + | |- | ||
| + | ! GPU | ||
| + | | Mali400MP2 GPU @600 MHz,Supports OpenGL ES 2.0 | ||
| + | |- | ||
| + | ! Memory | ||
| + | | 1GB DDR3 (shared with GPU) | ||
| + | |- | ||
| + | ! Onboard Network | ||
| + | | 10/100/1000 Ethernet | ||
| + | |- | ||
| + | ! Onboard WIFI | ||
| + | | SDIO AP6212（option AP6181 AP6335） | ||
| + | |- | ||
| + | ! Video Input | ||
| + | | A CSI input connector Camera:1 Supports 8-bit YUV422 CMOS sensor interface,2 Supports CCIR656 protocol for NTSC and PAL, 3 Supports SM pixel camera sensor, 4 Supports video capture solution up to 1080p@30fps | ||
| + | |- | ||
| + | ! Video Outputs | ||
| + | | Supports HDMI output with HDCP, Supports HDMI CEC, Supports HDMI 30 function, Integrated CVBS, Supports simultaneous output of HDMI and CVBS | ||
| + | |- | ||
| + | ! Audio Outputs | ||
| + | | HDMI | ||
| + | |- | ||
| + | ! Power Source | ||
| + | | DC input can supply power, but USB OTG input don’t supply power | ||
| + | |- | ||
| + | ! USB 2.0 ports | ||
| + | | two USB 2.0 HOST, one USB 2.0 OTG | ||
| + | |- | ||
| + | ! GPIO | ||
| + | | 40 Pins Header,compatible with Raspberry Pi B+ | ||
| + | |- | ||
| + | ! LED | ||
| + | | Power led & Status led | ||
| + | |- | ||
| + | ! IR | ||
| + | | IR input on board | ||
| + | |- | ||
| + | ! OS | ||
| + | | Android, Ubuntu, Debian, Raspberry Pi Image | ||
| + | |} | ||
| + | {{clear}} | ||
==GPIO PIN define == | ==GPIO PIN define == | ||
Revision as of 23:32, 6 May 2018
Contents
Introduction
Key Features
Getting Start
Hardware
Hardware interfact
File:BPI-M2 plus interface.jpg
Hardware spec
| Banana Pi M2+(Plus) | |
|---|---|
| CPU | H3 Quad-core Cortex-A7 H.265/HEVC 4K |
| GPU | Mali400MP2 GPU @600 MHz,Supports OpenGL ES 2.0 |
| Memory | 1GB DDR3 (shared with GPU) |
| Onboard Network | 10/100/1000 Ethernet |
| Onboard WIFI | SDIO AP6212（option AP6181 AP6335） |
| Video Input | A CSI input connector Camera:1 Supports 8-bit YUV422 CMOS sensor interface,2 Supports CCIR656 protocol for NTSC and PAL, 3 Supports SM pixel camera sensor, 4 Supports video capture solution up to 1080p@30fps |
| Video Outputs | Supports HDMI output with HDCP, Supports HDMI CEC, Supports HDMI 30 function, Integrated CVBS, Supports simultaneous output of HDMI and CVBS |
| Audio Outputs | HDMI |
| Power Source | DC input can supply power, but USB OTG input don’t supply power |
| USB 2.0 ports | two USB 2.0 HOST, one USB 2.0 OTG |
| GPIO | 40 Pins Header,compatible with Raspberry Pi B+ |
| LED | Power led & Status led |
| IR | IR input on board |
| OS | Android, Ubuntu, Debian, Raspberry Pi Image |
GPIO PIN define
Banana Pi BPI-M2+ (BPI-M2 Plus) has a 40-pin GPIO header that matches that of the Model Raspberry Pi 3. Following is the Banana Pi GPIO Pinout:
Error creating thumbnail: Unable to save thumbnail to destination
Software
Android
Linux
Opnewrt
TinaLinux
Allwinner Tina-IoT os for BPI-M2 Ultra/BPI-M2 Berry
