Getting Started with BPI-M6 - Revision history

Squy: /* Linux */

2024-05-31T01:47:49Z

‎Linux

Squy: /* Prepare */

2024-01-04T09:46:20Z

‎Prepare

Squy: /* Linux */

2023-12-19T03:42:52Z

‎Linux

Squy: /* Prepare */

2023-11-08T07:02:17Z

‎Prepare

Squy at 03:29, 6 November 2023

2023-11-06T03:29:41Z

Squy: /* Linux */

2023-11-03T08:29:38Z

‎Linux

Squy: /* specifications */

2023-09-27T02:51:04Z

‎specifications

Squy: /* Prepare */

2023-09-22T02:31:44Z

‎Prepare

Squy: /* Install Image with Usb Burning Tool */

2023-09-20T10:01:38Z

‎Install Image with Usb Burning Tool

Squy: /* Prepare */

2023-09-20T08:23:20Z

‎Prepare

← Older revision		Revision as of 01:47, 31 May 2024
Line 74:		Line 74:

	:After the image is burned, insert the SD card into the BPI-M6. Press and hold the SPI key while inserting the power supply.		:After the image is burned, insert the SD card into the BPI-M6. Press and hold the SPI key while inserting the power supply.
		+
		+	=== HDMI===
		+	VS680 HDMI TX functional properties:
		+
		+	* Support hdmi v2.1
		+	* Support up to 2160p@60 YUV444
		+	* Support up to 1080p@60 with 12b deep color
		+	* Support up to HDCP 2.2
		+	* Support HBR output
		+	* Support HDR10 and HLG
		+
		+	==== HDMI TX software configuration====
		+	VS680 currently uses two display frameworks, FB and DRM
		+
		+	Source code file for FB scheme:
		+	:syna-release/linux_5_4/drivers/video/syna/source/
		+
		+	Source code file for DBM scheme:
		+	:syna-release/linux_5_4/drivers/soc/berlin/modules/drm/
		+
		+	Enable the HDMI TX feature in the configuration file. The configuration file is located in the SDK's '''syna-release/configs/product/vs680_a0_android_baseline_evk/vs680_a0_android_baseline_evk_defconfig'''，with the following configuration:
		+	::[[File:bpi-m6_hdmi_tx_software_configuration.png]]
		+
		+
		+	==== Enable HDCP====
		+
		+	test_disp enable/disable hdcp
		+	test_disp setVersion 1 //set hdcp 1.4
		+	test_disp setVersion 2 //set hdcp 2.2
		+
		+
		+	==== Resolution Configuration====
		+	Supported standards: CEA-861-E video format
		+
		+	Supported resolutions:
		+
		+	* 3840x2160p60Hz/30Hz//24Hz
		+	* 1920x1200@60hz
		+	* 1920x1080p@60
		+	* 1280x700p@60
		+
		+	Configure resolution and format on the command line:
		+
		+	test_disp setformat[Display ID] [Resolution ID] [BitDepth] [Color fmt] [Aspect Ratio][tgID][vout_mode]
		+
		+	Examples:
		+	test_disp setformat 0 64 2 0
		+
		+
		+
		+	=== Ethernet ===
		+
		+
		+	=== WiFi & BT ===
		+	There are two ways to use WiFi & BT.
		+
		+	Purchase BPI-M6 CSI · WiFi accessories. Insert it into the M.2 Key E interface, and then insert a network card on the accessories.
		+
		+	WiFi&BT accessories using USB interface.
		+
		+	=== Camera ===
		+
		+	You can purchase BPI-M6 CSI · WiFi accessories.There are two CSI interfaces above.

@@ Line 26: / Line 26: @@
 ==Prepare==
-:1. Prepare a usb-serial cable, a 5V/3A adaptor type-c power supply. The serial cable is used for console debug and type-c cable is used for android image download.
+:1. Prepare a usb-serial cable('''3.3V,Baud: 115200'''), a 5V/3A adaptor type-c power supply. The serial cable is used for console debug and type-c cable is used for android image download.
 :2. Prepare a SDcard at least 8GB for linux development, android only support emmc boot.
 ==Android==
 ===Prepare===

← Older revision		Revision as of 03:42, 19 December 2023
Line 57:		Line 57:

	==Linux==		==Linux==
		+	===Install Image to SD card===
		+
		+	:Install Image with Balena Etcher.
		+
		+	:[https://balena.io/etcher Balena Etcher] is an opensource GUI flash tool by Balena, Flash OS images to SDcard or USB drive.
		+
		+	::Click on "'''Flash from file'''" to select image.
		+
		+	::Click on "'''Select target'''" to select USB device.
		+
		+	::Click on "'''Flash!'''" Start burning.
		+
		+	::[[File:etcher.jpg]]
		+
		+	:After the image is burned, insert the SD card into the BPI-M6. Press and hold the SPI key while inserting the power supply.

@@ Line 31: / Line 31: @@
 ===Prepare===
-:1. Download and install the [https://download.banana-pi.dev/d/ca025d76afd448aabc63/files/?p=%2FTools%2Fimage_download_tools%2FSenarySocSystemToolSetupV1.3.2.1.zip SenarySocSystemTool] for android image download via USB type-c on M6, only support windows.
+:1. Download and install the [https://download.banana-pi.dev/d/ca025d76afd448aabc63/files/?p=%2FTools%2Fimage_download_tools%2FSenarySocSystemToolSetupV1.3.2.1.rar SenarySocSystemTool] for android image download via USB type-c on M6, only support windows.
 :2. Download the latest android image, and confirm that the md5 checksum is correct.

← Older revision		Revision as of 03:29, 6 November 2023
Line 53:		Line 53:

	:5. If you want to erase eMMC, you can repeat the above steps, but you need to click on Erase eMMC instead of starting the burn.		:5. If you want to erase eMMC, you can repeat the above steps, but you need to click on Erase eMMC instead of starting the burn.
		+
		+	NOTE: Android images currently only support burning to EMMC.

	==Linux==		==Linux==
−
−	~~:Install Image with Balena Etcher.~~
−	~~:[https://balena.io/etcher Balena Etcher] is an opensource GUI flash tool by Balena, Flash OS images to SDcard or USB drive.~~
−
−	~~:1.Click on "Flash from file" to select image. Click on "Select target" to select USB device. Click on "Flash!" Start burning.~~
−
−	~~:[[File:Etcher.jpg]]~~
−
−	~~:2.After the image is burned, insert the SD card into the BPI-M6. Press and hold the SPI key while inserting the power supply.~~

← Older revision		Revision as of 08:29, 3 November 2023
Line 55:		Line 55:

	==Linux==		==Linux==
		+
		+	:Install Image with Balena Etcher.
		+	:[https://balena.io/etcher Balena Etcher] is an opensource GUI flash tool by Balena, Flash OS images to SDcard or USB drive.
		+
		+	:1.Click on "Flash from file" to select image. Click on "Select target" to select USB device. Click on "Flash!" Start burning.
		+
		+	:[[File:Etcher.jpg]]
		+
		+	:2.After the image is burned, insert the SD card into the BPI-M6. Press and hold the SPI key while inserting the power supply.

@@ Line 5: / Line 5: @@
-Banana Pi BPI-M6 is the next generation single board computer from Banana Pi in 2022,It is powered by Synaptics VS680 quad-core Cortex-A73 (2.1GHz) and One Cortex-M3 processor,Imagination GE9920 GPU.and NPU Up to 6 .75Tops. Onboard 4GB LPDDR4 memory and 16GB EMMC storage, and supports 4 USB 3.0 interface, a gigabit network port.onboard 1 HDMI-rx port and 1 Hdmi-tx port.
+Banana Pi BPI-M6 is a new generation single board computer design , use Synaptics VS680 quad-core Cortex-A73 (2.1GHz) and One Cortex-M3 processor,Imagination GE9920 GPU.and NPU Up to 6 .75Tops. Onboard 4GB LPDDR4 memory and 16GB EMMC storage, and supports 4 USB 3.0 interface, a gigabit network port.onboard 1 HDMI-rx port and 1 Hdmi-tx port.
 =specifications=
 =development=

@@ Line 25: / Line 25: @@
 :[[File:m6_android_install_1.png]]
 :2. Press the USB button next to type-c and connect to the computer using the type-c cable.
 :3. Click to start burning, and then wait for the burning to complete.
-:4. After Burning successfull, Unplug the usb and connect to power supply adaptor to startup.
+:5. If you want to erase eMMC, you can repeat the above steps, but you need to click on Erase eMMC instead of starting the burn.
 ==Linux==